JOTON | Sự khác biệt đến bất ngờ !

Industrial

other products

JONA® EPO CLEAR

JONA® EPO CLEAR is a transparent coating for solvent-free concrete floors, Epoxy resin base consists of 2 components, evenly spread out, giving a seamless finish, capable of executing at high thickness. Used in many fields from industrial floors with light loads and floor types that require long-term protection against chemicals and abrasives such as warehouses, laboratories, factories, industrial plants, diseases institute.

Surface material: Concrete

Features Bearing, impact resistant, abrasive and very good chemicals. Can be applied at 1-3 mm thickness (depending on construction method).

JONA® EPO METALLIC

JONA® EPO METALLIC is a coating for solvent-free concrete floor, Epoxy resin base consists of 2 components, self-spreading, for a seamless finish surface, capable of executing at high thickness. Used in many fields from industrial floors with light loads and floor types that require long-term protection against chemicals and abrasives such as warehouses, laboratories, factories, industrial plants, diseases institute.

Surface material: Concrete

Features Bearing, impact resistant, abrasive and very good chemicals. Can be applied at 1-3 mm thickness (depending on construction method).

JONA® LEVEL (A)

JONA®LEVEL is the three-component epoxy coating without solvent. It is self leveling and homogeneous. It could be practiced in different thicknesses. (depend on the surface conditions) It is used for floors of storage, workshop, plant, factory, laboratory etc., in order to protect them against abrasion and chemical influence. It is possible for medium loading on.

Surface material: For new concrete floor, it demands the time of at least 28 days to solidify completely. The concrete has to meet technical requirements such as the mixing ratio of water with cement, used additives, durability requirement of concrete, etc. The practiced surface humidity is not more than 4%. The humidity of practiced space is not more than 85%. The practiced surface should be completely cleaned. Oil, grease and chemical substances should be removed. Filling and leveling the holes and cracks on the surface (if any). The practiced surface should be leveled well. The surface preparation is completed on the day before it should be cleaned dirt again by suction before practiced. The recoating is carried out during the incompletion solidification of previous coating will get the best adhesion. If the recoating time is beyond the recommendation, the surface should be roughened again before recoating.

Features Standing weight, impact, abrasion and chemical influence well. The thickness practice from 1-3mm is possible. (depend on practice method)

JONES® CONC (A)

JONES® CONC is the two-component epoxy primer solidified by Polyamide or Amine. It is used as the primer of coating system for floor in industrial area in order to increase adhesion, resist to alkalization of the finish on concrete surfaces.

Surface material: The practiced surface should be clean. The dilute detergent or solvent should be used to remove oil and grease. For exterior surface, jet-water can be used. Filling and leveling the holes and cracks on the surface with suitable materials. The uneven surface will increase adhesion. The surface humidity is not more than 4%.

Features Good adhesion on kinds of floor coating and of concrete surface. Resistance to water, solvent and chemical.

JONES® EPO

JONES® EPO is the two-component epoxy primer solidified by Polyamide or Amine. It is compatible with most of another Chlorinated rubber, Polyurethane and Epoxy. Used to increase adhesion, alkali prevention effect for coatings on concrete and anti-rust substrates to protect metal parts for industrial plants, chemical, fuel, sea water, and biological water tanks active ... JONES® EPO has been certified as conforming to the JAPANESE INDUSTRIAL STANDARD JIS K 5551:2008

Surface material: Bare steel: To get the best finish, the cleaning with abrasive blast should be conformed to SA 21/2, and the removing oil and grease with solvent should be conformed to SSPC-SP1. Shopprimed steel: Clean, dry and undamaged approved shopprimer. For the concrete surfaces, the wet cloths should be used for cleaning dirt and other same contaminants. The dilute detergent or solvent should be used for removing oil and grease. For exterior surfaces, jet-water can be used. Filling and leveling the holes and cracks on the surface with suitable materials. The rough surface will increase adhesion. The surface humidity is not more than 12%.

Features High adhesion on metal, concrete, wood, plastic surfaces. Resistant to acid, salt, gasoline, seawater, fresh water and foods.

JONES® EPO CLEAR

Surface material:

Features

JONES® SEALER (A)

JONES®SEALER is the two-component epoxy primer without solvent, solidified by Polyamide or polyamine. It is compatible with most of another Polyurethane and Epoxy. It is used as the primer of industrial floor coating system for increasing adhesion, resisting to alkalization of the finish on concrete surfaces.

Features Good adhesion on kinds of floor coating and most of concrete surfaces. Resistance to water, solvent and chemical. Good solidification in spite of dripping wet floor. Practicing directly on surface with high humidity is possible.

JONES®MORTAR (A)

JONES® MORTAR is a buffer for solvent-free concrete floor, epoxy resin system consists of 3 components, for seamless surface finish, capable of executing in many different thicknesses depending on the purpose for each type different floor. Used for medium-sized industrial floors and floors that require long-term protection against chemicals and abrasives such as warehouses, laboratories, factories, industrial plants.

Surface material: Concrete

Features Bearing, impact resistant, abrasive and very good chemicals. Can be applied at a thickness of 2-10 mm (depending on the method of construction)