Surface material: The practiced surface should be clean, dry and free oil, grease and chalking.

Features JONA® EPO is a two-component epoxy paint, solvent system. On steel substrates: protect metal surfaces, tanks that require food safety requirements, and require complete epoxy system coating.

Surface material: Concrete

Features Bearing, impact resistant, abrasive and very good chemicals. Can be applied at 1-3 mm thickness (depending on construction method).

Surface material: Concrete

Features Bearing, impact resistant, abrasive and very good chemicals. Can be applied at 1-3 mm thickness (depending on construction method).

Surface material: The practiced surface should be clean, dry and free oil, grease and chalking.

Features Practice easily Standing impact and abrasion well. Add the hardness and toughness to the film. Heat-resistant up to 1100C (un-continuous).

Surface material: For new concrete floor, it demands the time of at least 28 days to solidify completely. The concrete has to meet technical requirements such as the mixing ratio of water with cement, used additives, durability requirement of concrete, etc. The practiced surface humidity is not more than 4%. The humidity of practiced space is not more than 85%. The practiced surface should be completely cleaned. Oil, grease and chemical substances should be removed. Filling and leveling the holes and cracks on the surface (if any). The practiced surface should be leveled well. The surface preparation is completed on the day before it should be cleaned dirt again by suction before practiced. The recoating is carried out during the incompletion solidification of previous coating will get the best adhesion. If the recoating time is beyond the recommendation, the surface should be roughened again before recoating.

Features Standing weight, impact, abrasion and chemical influence well. The thickness practice from 1-3mm is possible. (depend on practice method)

Surface material: Concrete, metal

Features Good adhesion.  Stand the impact and abrasion well. Resistance to fungus and alga. Good water-resistant.

Surface material: The practiced surface should be clean and free from the contamination of dirt, oil, wax, chalking, mildew and other chemical agents in order to ensure proper adhesion to the substrate. The jet- water can be used for cleaning after that. The prior coating (if any) has to be moved by sanded or abraded. Filling the holes and cracks on the surface and/ or leveling with JOTON® WEPO. For the new concrete (in normal conditions), practicing is only allowed after 28 days.

Features   Practice and clean tools easily. Durability and fast color film. Standing impact, abrasion, chemical and the influences of weather well. Safety in application because of the used water thinner.

Surface material: The practiced surface should be clean. The dilute detergent or solvent should be used to remove oil and grease. For exterior surface, jet-water can be used. Filling and leveling the holes and cracks on the surface with suitable materials. The uneven surface will increase adhesion. The surface humidity is not more than 4%.

Features Good adhesion on kinds of floor coating and of concrete surface.    Resistance to water, solvent and chemical.

Surface material: Bare steel: To get the best finish, the cleaning with abrasive blast should be conformed to SA 21/2, and the removing oil and grease with solvent should be conformed to SSPC-SP1. Shopprimed steel: Clean, dry and undamaged approved shopprimer. For the concrete surfaces, the wet cloths should be used for cleaning dirt and other same contaminants. The dilute detergent or solvent should be used for removing oil and grease. For exterior surfaces, jet-water can be used. Filling and leveling the holes and cracks on the surface with suitable materials. The rough surface will increase adhesion. The surface humidity is not more than 12%.

Features High adhesion on metal, concrete, wood, plastic surfaces. Resistant to acid, salt, gasoline, seawater, fresh water and foods.

Features

Surface material: The practiced surface should be clean. The dilute detergent or solvent should be used to remove oil and grease. For exterior surface, jet-water can be used. Filling and leveling the holes and cracks on the surface with suitable materials. The rough surface will make the adhesion to be more.

Features Good adhesion on kinds of floor coating and most of concrete surfaces.      Resistance to water, solvent and chemical. Good solidification in spite of dripping wet floor. Practicing directly on surface with high humidity is possible.

Surface material: The practiced surface should be clean and free from the contamination of dirt, oil, grease, wax, chalking, mildew and other chemical agents in order to ensure proper adhesion to the substrate. The jet- water can be used for cleaning after that. The prior coating (if any) has to be moved by sanded or abraded. Filling and leveling the holes, cracks on the surface with JOTON® WEPO. For the new concrete (in normal conditions), practicing is only allowed on 28 days after.

Features  Practice and clean tools easily.  Good adhesion. Standing humidity and chemical well. Durability. Resistance to alga and fungus. Resistance to the alkalization of concrete surface. Safety in application because of the used water thinner.